FREE SHIPPING
on Safety Orders Over $99 or $8.99 Flat Rate Shipping on Orders Below $99 *Exclusions Apply*
IMPORTANT SHIPPING INFORMATION
Time-Sensitive Order?
Call 877-902-9417 or email cs@rajsupply.com to verify availability and shipping lead time.
PIP 33-VRX180 G-Tek VR-X Seamless Knit Nylon Glove with Polyurethane Advanced Barrier Protection Coating on Full Hand – Touchscreen Compatible – Dozen
$51.26
Ideal for handling and assembly of small to medium sharp parts and materials, manufacturing, inspection, shipping and packaging and mechanical equipment maintenance and repair.
FEATURES
- Seamless construction offers increased comfort and breathability
- Nylon blended shell, featuring an ultra-thin 18 gauge liner for exceptional dexterity
- VR-X Polyurethane coatings provide advanced barrier protection, the treated coating takes on the surface properties of the glove liner providing a tactile grip in wet, dry and slightly oily conditions, ideal for applications that require dexterity for precise handling
- Liquid proof, air leak tested – EN374-2
- Antibacterial and antiviral barrier protection per ISO 20743:2013 test method & EN374-5
- ESD Safe, Surface Resistance per ESD S11.11 Static dissipative range at 10^8 ohms, 12%RH, 48hrs @100Volts
- 4.0 AQL, similar to the AQL levels for industrial grade disposable gloves
- Touchscreen compatible to allow the user to operate a touch screen phone or device without removing gloves
- Silicone free
- Knit Wrist helps prevent dirt and debris from entering the glove
- Color coded hems for easy size identification
- Washable, resistant to water and ultraviolet light
- Recommended wash cycle: maximum 6 cycles
- WARNING: Cancer – www.P65Warnings.ca.gov
EN388 RESULTS: 3111XX
EN 388 2016 Results:Abrasion: 3Cut (Coupe Test): 1Tear: 1Puncture: 1Cut (TDM-100 Test): XImpact Protection: X
EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove’s ratings. Click here for more information about the EN 388 2016 standard.
ANSI ABRASION LEVEL: 1
Test Method: ASTM D3389-10
The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3389-10 test is used for coated gloves and the end point (failure) is the number of abrasion cycles it takes for the coating to wear through. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.
ANSI PUNCTURE LEVEL: 2
Test Method: ASTM F1342
The ANSI/ISEA 105-2016 blunt puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.
END OF LIFE – RECYCLABLE VIA TERRACYCLE® PROGRAM
Whether it’s earplugs, gloves, safety eyewear or other recyclable PPE used in a manufacturing facility or jobsite, PIP®, in collaboration with TerraCycle® provides an easy and convenient way of collecting used PPE to help reduce the amount of waste that ends up in landfills. Contaminated PPE cannot be recycled. Learn More.
EXTENDED LIFE – REUSABLE/LAUNDERABLE
Reusing or laundering products not only reduces cost, but also reduces the amount of waste that is put into our landfills in turn reducing the environmental impact.
| Size |
X-Small ,Small ,Medium ,Large ,XLarge ,2X |
|---|---|
| Brand | |
| Material |
Nylon / Poly |
| Package Quantity |
12 Pairs |
| Thickness |
18 Gauge |
| Style |
General Purpose / Poly Coated |
It is important to know how to measure the hand to get a proper fitting glove. Measuring the hand for correct fit will give the employee the best possible protection without compromising the task, duty or safety of the wearer. There are two suggested ways to find the correct glove size. One way is to measure the width of the hand — measure around the hand (a dominant hand measurement is preferred) with a tape measure as shown below. The dominant hand will be the right if you are right-handed and left if you are left-handed.
If the gloves you are purchasing come in numbered sizes, you can relate the measurement directly to the numerical size listed for the glove. For example, if the measurement taken is exactly eight inches (203 millimeters) then you would select a size eight glove. To avoid hand fatigue, order the next larger size for all measurements that are not exact inch/millimeter measurements. If the gloves you are purchasing come in extra-small (XS), small (S), medium (M), large (L), extra-large (XL) or double extra-large (XXL), use the table below to translate the inch/millimeter measurement.
If the gloves you are purchasing come in numbered sizes, you can relate the measurement directly to the numerical size listed for the glove. For example, if the measurement taken is exactly eight inches (203 millimeters) then you would select a size eight glove. To avoid hand fatigue, order the next larger size for all measurements that are not exact inch/millimeter measurements. If the gloves you are purchasing come in extra-small (XS), small (S), medium (M), large (L), extra-large (XL) or double extra-large (XXL), use the table below to translate the inch/millimeter measurement.
| US Sizes | EU Sizes | ||
| 6–7 Inches | XS | 152–178 Milimeters | EU – 6 |
| 7–8 Inches | S | 178–203 Milimeters | EU – 7 |
| 8–9 Inches | M | 203–229 Milimeters | EU – 8 |
| 9–10 Inches | L | 229–254 Milimeters | EU – 9 |
| 10–11 Inches | XL | 254–279 Milimeters | EU – 10 |
| 11 + Inches | XXL | 279 + Milimeters | EU – 11 |
Source: Turtleskin Glove/Warwick Mills, Inc.
Another method is to measure the length of your hand by measuring from the bottom edge of the palm to the tip of the longest finger as illustrated below.
| US Sizes | EU Sizes | ||
| 6 5/16 Inches | XS | 160 Milimeters | EU – 6 |
| 6 3/4 Inches | S | 171 Milimeters | EU – 7 |
| 7 3/16 Inches | M | 182 Milimeters | EU – 8 |
| 7 9/16 Inches | L | 192 Milimeters | EU – 9 |
| 8 1/16 Inches | XL | 204 Milimeters | EU – 10 |
| 8 7/16 + Inches | XXL | 215 + Milimeters | EU – 11 |
Source: Turtleskin Glove/Warwick Mills, Inc.
There are six (6) classes of electrical gloves, and you know which class you need based on the voltages you will be working with. You can find the full OSHA guidelines in standard 29 CFR 1910.137
- Class 00 – Protects workers up to 500 VAC and 750 VDC
- Class 0 – Protects workers up to 1,000 VAC and 1,500 VDC
- Class 1 – Protects workers up to 7,500 VAC and 11,250 VDC
- Class 2 – Protects workers up to 17,000 VAC and 25,000 VDC
- Class 3 – Protects workers up to 26,500 VAC and 39,750 VDC
- Class 4 – Protects workers up to 36,000 VAC and 54,000 VDC
6843 N. Citrus Ave Ste. W Crystal River, Florida 34428 USA
We offer logo service on many of the PPE products we sell. To receive a custom quote please use this request form.
Related products
ATG MaxiDry 56-424 Ultra Lightweight Nitrile Glove, Palm Dipped with Seamless Knit Nylon – Dozen
ATG MaxiFlex 34-846 Endurance Seamless Knit Nylon Glove with Nitrile Coated MicroFoam Grip on Full Hand – Dozen
DEWALT DPG250 Vibration Reducing Premium Padded Glove, Pair (CLOSEOUT)
PIP 07-KA700 Kut Gard A5 Seamless Knit ACP / Kevlar Blended Glove – Polyester Lining – Heavy Weight – Dozen
PIP 09-H550SLPV Scrap King Seamless Knit PolyKor Engineered Yarn Glove – Split Cowhide Leather Palm and Kevlar Stitching – Pair
