on Safety Orders Over $99 or $8.99 Flat Rate Shipping
on Orders Below $99 *Exclusions Apply*
Free shipping
PIP 56-586CR Assurance Cut Level A4 Nitrile Coated Glove with PolyKor Blended Liner and MicroFinish Grip on Palm & Fingers - 14" - Dozen
As low as
$197.40
Available
Eligible for Free Shipping
Allow 1-3 Business Days to Ship
Details
Assurance® cut resistant chemicals gloves were designed and developed for those working with chemicals while also requiring a level of cut protection.
FEATURES
- Nitrile polymer provides excellent grip in wet, oily and dry conditions
- PolyKor® blended liner is lightweight and provides excellent dexterity, tactile sensitivity, and cut resistance
- MicroFinish coatings are infused with thousands of tiny suction cup pockets that create a vacuum effect that dispenses fluids away on contact
- MicroFinish™ coating provides excellent resistance to liquid permeation
- Tested to EN 374-5:2016 for protection against micro-organisms
- Strong protection to punctures and abrasions
ANSI CUT LEVEL: A4
Test Method: ASTM F2992-15
New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.
EN 388 2016 RESULTS: 4X42DX
Abrasion: 4Cut (Coupe Test): XTear: 4Puncture: 2Cut (TDM-100 Test): DImpact Protection: X
EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove's ratings. Click here for more information about the EN 388 2016 standard.
ANSI ABRASION LEVEL: 6
Test Method: ASTM D3884-09
The ANSI/ISEA 105-2016 standard outlines test methods for abrasion and is scored from 0-6. The ASTM D3884-09 is used for uncoated gloves and the end point (failure) is the number of abrasion cycles when the first thread or yarn is broken. The larger numbers of cycles indicates greater abrasion resistance of the product and a higher ANSI Abrasion Level.
ANSI PUNCTURE LEVEL: 3
Test Method: ASTM F1342
The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.
PROTECTIVE GLOVES AGAINST MICRO-ORGANISMS BACTERIA AND FUNGI
The EN ISO 374-5 standard measures the ability of gloves to protect users against bacteria and fungi. Gloves with this marking must pass EN374-2 for leak testing.
Chemical Permeation
The chemical permeation of our product is measured in accordance to European Standard EN 374-3. This measures the resistance of protective gloves against chemicals and microorganisms. Part 3 of the standard determines the level of resistance to permeation by chemicals.
Breakthrough Time (BTT)
The number of minutes from initial contact with a test chemical until it is first detected on the inside of the glove.
Breakthrough Time - Protection Index
Each chemical tested is classified in terms of breakthrough time (performance level 0 to 6).
CAUTION: This information is provided as an aid in determining the general suitability of various products for use with specific chemicals. These recommendations are advisory only and the SUITABILITY OF THE PRODUCT FOR A SPECIFIC APPLICATION OR ENVIRONMENT MUST BE DETERMINED BY THE PURCHASER OR USER OF THE PRODUCT. This information should be used as a guide only.
Chemical Name |
Level |
BTT |
|---|---|---|
| Acetic acid, 99% | 66 MIN | |
| Ammonium hydroxide, 25% | 480 MIN | |
| Formaldehyde, 37% | 480 MIN | |
| Formaldehyde, 37% | 480 MIN | |
| Hydrogen peroxide, 30% | 480 MIN | |
| Methanol | 64 MIN | |
| n-Heptane | 292 MIN | |
| Nitric acid 65% | 94 MIN | |
| Sodium hydroxide, 40% | 480 MIN | |
| Sulfuric acid, 96% | 61 MIN |