FREE SHIPPING
on Safety Orders Over $99 or $8.99 Flat Rate Shipping on Orders Below $99 *Exclusions Apply*
IMPORTANT SHIPPING INFORMATION
Time-Sensitive Order?
Call 877-902-9417 or email cs@rajsupply.com to verify availability and shipping lead time.
Ideal for Tig welding and automotive assembly.
Features
- Top Grain Kidskin leather construction is lightweight and more supple compared to goatskin
- Para-aramid blended lining provides 360 degree added cut and heat resistance, which extends down thru the gauntlet cuff
- Provides electrical resistance with an APTV rating of 37 cal/cm2
- Stitched with Kevlar® adding strength and burn resistance
- Flame Resistant TPR (Thermo Plastic Rubber) back-of-hand impact protection to knuckles and fingers by dispersing impact force energy away from the bone, without sacrificing dexterity
- Keystone thumb is ergonomic, reduces hand fatigue, offers superior dexterity and durability
- Split cowhide 4.5″ leather gauntlet cuff for added forearm protection and allows for easy on and off
- Meets the content requirements for Chromium VI free leather
ANSI Cut Level: A4
Test Method: ASTM F2992-15
New edition ANSI/ISEA 105-2016 outlines a new test method for determining cut scores and a revised scale from A1-A9. Click here for more information about the new testing standard.
EN 388 2016 Results: 3X22DP
Abrasion: 3Cut (Coupe Test): XTear: 2Puncture: 2Cut (TDM-100 Test): DImpact Protection: P
EN 388 is a European Standard. Cut Level is determined by the number of cycles it takes a spinning circular blade, that is pulled across the material under a constant weight of 500 grams, to cut the fabric. As the number of cycles increase, so does the glove’s ratings. Click here for more information about the EN 388 2016 standard.
ANSI Puncture Level: 3
Test Method: ASTM F1342
The ANSI/ISEA 105-2016 blunt force puncture testing uses a probe to simulate a tear or burst hazard. The test measures the amount of force needed for a blunt probe to pierce through PPE material. Results are given in Newtons, which is converted into a 1-5 scale and spans from 10 newtons (Level 1) to 150+ newtons (Level 5) of puncture resistance.
ANSI Impact Level: 2
ANSI/ISEA 138 is a new, voluntary standard for the North American market designed to accurately classify different levels of impact protection offered by the impact-resistant gloves on the market. Click here for more information on our G-Tek Impact Series.
Test Method: ASTM F1060-18Temperature: 392°F
The ANSI/ISEA 105-2016 standard outlines test methods for contact heat and scored from 0-5. The ASTM F1060-18 test is used to test conductive heat resistance against gloves and PPE. Measuring the highest contact temperature for which the time to second-degree burn is at least 15 seconds and the alarm time is at least four seconds. Learn More
PPE Category: 3
ATPV 37 Cal/cm2
The NFPA has identified the various FR hazardous risk category levels, which range from PPE 1 (which is low risk and requires AR clothing with a minimum arc rating of 4), up to PPE 4 (which is high risk and requires AR clothing with a minimum arc rating of 40). Each level, 1-4, is rated at a certain amount of flame resistance measured in cal/cm2.
| Size |
Small ,Medium ,Large ,XLarge ,2X ,3X |
|---|---|
| Brand | |
| ANSI Cut Level |
A4 |
| Liner Material |
Aramid |
| Package Quantity |
1 Pair |
| Style |
Cut Resistant Gloves |
It is important to know how to measure the hand to get a proper fitting glove. Measuring the hand for correct fit will give the employee the best possible protection without compromising the task, duty or safety of the wearer. There are two suggested ways to find the correct glove size. One way is to measure the width of the hand — measure around the hand (a dominant hand measurement is preferred) with a tape measure as shown below. The dominant hand will be the right if you are right-handed and left if you are left-handed.
If the gloves you are purchasing come in numbered sizes, you can relate the measurement directly to the numerical size listed for the glove. For example, if the measurement taken is exactly eight inches (203 millimeters) then you would select a size eight glove. To avoid hand fatigue, order the next larger size for all measurements that are not exact inch/millimeter measurements. If the gloves you are purchasing come in extra-small (XS), small (S), medium (M), large (L), extra-large (XL) or double extra-large (XXL), use the table below to translate the inch/millimeter measurement.
If the gloves you are purchasing come in numbered sizes, you can relate the measurement directly to the numerical size listed for the glove. For example, if the measurement taken is exactly eight inches (203 millimeters) then you would select a size eight glove. To avoid hand fatigue, order the next larger size for all measurements that are not exact inch/millimeter measurements. If the gloves you are purchasing come in extra-small (XS), small (S), medium (M), large (L), extra-large (XL) or double extra-large (XXL), use the table below to translate the inch/millimeter measurement.
| US Sizes | EU Sizes | ||
| 6–7 Inches | XS | 152–178 Milimeters | EU – 6 |
| 7–8 Inches | S | 178–203 Milimeters | EU – 7 |
| 8–9 Inches | M | 203–229 Milimeters | EU – 8 |
| 9–10 Inches | L | 229–254 Milimeters | EU – 9 |
| 10–11 Inches | XL | 254–279 Milimeters | EU – 10 |
| 11 + Inches | XXL | 279 + Milimeters | EU – 11 |
Source: Turtleskin Glove/Warwick Mills, Inc.
Another method is to measure the length of your hand by measuring from the bottom edge of the palm to the tip of the longest finger as illustrated below.
| US Sizes | EU Sizes | ||
| 6 5/16 Inches | XS | 160 Milimeters | EU – 6 |
| 6 3/4 Inches | S | 171 Milimeters | EU – 7 |
| 7 3/16 Inches | M | 182 Milimeters | EU – 8 |
| 7 9/16 Inches | L | 192 Milimeters | EU – 9 |
| 8 1/16 Inches | XL | 204 Milimeters | EU – 10 |
| 8 7/16 + Inches | XXL | 215 + Milimeters | EU – 11 |
Source: Turtleskin Glove/Warwick Mills, Inc.
There are six (6) classes of electrical gloves, and you know which class you need based on the voltages you will be working with. You can find the full OSHA guidelines in standard 29 CFR 1910.137
- Class 00 – Protects workers up to 500 VAC and 750 VDC
- Class 0 – Protects workers up to 1,000 VAC and 1,500 VDC
- Class 1 – Protects workers up to 7,500 VAC and 11,250 VDC
- Class 2 – Protects workers up to 17,000 VAC and 25,000 VDC
- Class 3 – Protects workers up to 26,500 VAC and 39,750 VDC
- Class 4 – Protects workers up to 36,000 VAC and 54,000 VDC
6843 N. Citrus Ave Ste. W Crystal River, Florida 34428 USA
We offer logo service on many of the PPE products we sell. To receive a custom quote please use this request form.
Related products
ATG MaxiChem 56-635 Nitrile Blend Coated Glove with Nylon / Lycra Liner and Non-Slip Grip on Palm & Fingers – 14″ – Pair (CLOSEOUT)
DEWALT DPG250 Vibration Reducing Premium Padded Glove, Pair (CLOSEOUT)
PIP 07-K350 Kut Gard Seamless Knit Kevlar Glove – Heavy Weight – A3 Cut Level – Dozen
PIP 09-H550SLPV Scrap King Seamless Knit PolyKor Engineered Yarn Glove – Split Cowhide Leather Palm and Kevlar Stitching – Pair
